MARIANI, MARCO
3D printing of fine alumina powders by binder jetting
2021-01-01 Mariani, Marco; Beltrami, Ruben; Brus, Paolo; Galassi, Carmen; Ardito, Raffaele; Lecis, NORA FRANCESCA MARIA
Additive manufacturing of lead-free KNN by binder jetting
2022-01-01 Mariani, Marco; Beltrami, Ruben; Migliori, Emanuele; Cangini, Laura; Mercadelli, Elisa; Baldisserri, Carlo; Galassi, Carmen; Lecis, Nora
Analysis of the Flatness Form Error in Binder Jetting Process as Affected by the Inclination Angle
2022-01-01 Zago, M; Lecis, N; Mariani, M; Cristofolini, I
Binder jetting 3D printing of 316 stainless steel: influence of process parameters on microstructural and mechanical properties
2021-01-01 Lecis, NORA FRANCESCA MARIA; Beltrami, Ruben; Mariani, Marco
Characterization of novel graphene-based microporous layers for Polymer Electrolyte Membrane Fuel Cells operating under low humidity and high temperature
2020-01-01 Mariani, M.; Latorrata, S.; Patrignani, S.; Gallo Stampino, P.; Dotelli, G.
Effect of printing parameters on sintered WC-Co components by binder jetting
2022-01-01 Mariani, Marco; Mariani, Davide; Pietro De Gaudenzi, Gian; Lecis, NORA FRANCESCA MARIA
Effects of process parameters, debinding and sintering on the microstructure of 316L stainless steel produced by binder jetting
2021-01-01 Lecis, N.; Mariani, M.; Beltrami, R.; Emanuelli, L.; Casati, R.; Vedani, M.; Molinari, A.
Employment of Micro- and Nano-WS2 Structures to Enhance the Tribological Properties of Copper Matrix Composites
2021-01-01 Freschi, Marco; Di Virgilio, Matteo; Zanardi, Gabriele; Mariani, Marco; Lecis, Nora; Dotelli, Giovanni
Evaluation of Graphene Nanoplatelets as a Microporous Layer Material for PEMFC: Performance and Durability Analysis
2019-01-01 Mariani, M.; Latorrata, S.; Gallo Stampino, P.; Dotelli, G.
Graphene oxide-naphthalene sulfonate blends as possible proton exchange membranes
2022-01-01 Di Virgilio, M.; Basso Peressut, A.; Latorrata, S.; Mariani, M.; Dotelli, G.
Graphene-based microporous layers for enhanced performance in PEM fuel cells
2020-01-01 Latorrata, Saverio; Mariani, Marco; GALLO STAMPINO, Paola; Cristiani, Cinzia; Dotelli, Giovanni
Influence of chemically synthesized powder addition on K0.5Na0.5NbO3 ceramic's properties
2022-01-01 Migliori, E; Mercadelli, E; Beltrami, R; Mariani, M; Baldisserri, C; Galassi, C; Lecis, N
Investigation of second phase concentration effects on tribological and electrical properties of Cu–WS2 composites
2022-01-01 Freschi, M.; Di Virgilio, M.; Haiko, O.; Mariani, M.; Andena, L.; Lecis, N.; Komi, J.; Dotelli, G.
Mechanical and microstructural characterization of WC-Co consolidated by binder jetting additive manufacturing
2021-01-01 Mariani, Marco; Goncharov, Ivan; Mariani, Davide; De Gaudenzi, Gian Pietro; Popovich, Anatoly; Lecis, Nora; Vedani, Maurizio
Optimization of perfluoropolyether-based gas diffusion media preparation for PEM fuel cells
2020-01-01 Balzarotti, R.; Latorrata, S.; Mariani, M.; Gallo Stampino, P.; Dotelli, G.
Tailoring α-alumina powder morphology through spray drying for cold consolidation by binder jetting
2022-01-01 Mariani, M.; Frias Blanco, G.; Mercadelli, E.; Sanchez-Herencia, A. J.; Galassi, C.; Lecis, N.; Ferrari, B.
The role of fluorinated polymers in the water management of proton exchange membrane fuel cells: A review
2021-01-01 Mariani, M.; Basso Peressut, A.; Latorrata, S.; Balzarotti, R.; Sansotera, M.; Dotelli, G.
Tuning the Parameters of Cu−WS2 Composite Production via Powder Metallurgy: Evaluation of the Effects on Tribological Properties
2023-01-01 Freschi, Marco; Dragoni, Lara; Mariani, Marco; Haiko, Oskari; Kömi, Jukka; Lecis, Nora; Dotelli, Giovanni