Sfoglia per Rivista KEY ENGINEERING MATERIALS
Analysis of fatigue damage accumulation in TiAl Intermetallics
2014-01-01 Beretta, Stefano; Filippini, Mauro; Patriarca, Luca; Sabbadini, Silvia
Calibration of constitutive law and ductile failure criterion for very thin rectangular Al2024-T3 aluminum alloy specimen
2012-01-01 Giglio, Marco; Gilioli, Andrea; Manes, Andrea
Classification of Problems Under Uncertainty, in FEM-Based Analysis and Design of Sheet Metal Forming Operations
2007-01-01 Strano, Matteo; Burdi, A.
Crystallographic analysis of specimens used for calibrate a failure model for an Al 6061 – T6 alloy
2012-01-01 Giglio, Marco; Manes, Andrea; Mapelli, Carlo; Mombelli, Davide; C., Baldizzone; Gruttadauria, Andrea
Damage mechanisms of initiating micro-pitting on 42CrMo4 hardened and tempered steel
2007-01-01 Barella, Silvia; Boniardi, MARCO VIRGINIO; Cincera, SILVIA MARIA; D'Errico, Fabrizio
Design of a Collagen/Silk Mechano-Compatible Composite Scaffold for the Vascular Tissue Engineering: Focus on Compliance
2007-01-01 F., Couet; N., Rajan; Vesentini, Simone; D., Mantovani
Determining elastic-plastic properties of Al6061-T6 from micro-indentation technique
2014-01-01 Amiri, Sina; Lecis, NORA FRANCESCA MARIA; Manes, Andrea; Mombelli, Davide; Giglio, Marco
Dislocation dynamics by measurements of dissipation
1990-01-01 Beghi, Marco
Economical comparison of cryogenic vs. Traditional turning of Ti-6Al-4V: A case study
2015-01-01 Tirelli, Stefano; Chiappini, Elio; Strano, Matteo; Monno, Michele; Semeraro, Quirico
Effect of REM finishing on fatigue behavior of a shot peened low alloy steel
2012-01-01 Bagherifard, Sara; Ghelichi, Ramin; Guagliano, Mario; M., Bandini
Effect of shot peening on residual stress and surface work hardening in cold sprayed coatings
2010-01-01 Bagherifard, Sara; I., Fernandez Pariente; Ghelichi, Ramin; Guagliano, Mario; S., Vezzù
Effect of triaxiality and Lode angle on the plasticity behaviour of a Ti-6Al-4V Titanium alloy
2014-01-01 Gilioli, Andrea; Manes, Andrea; Giglio, Marco; Allahverdizadeh, Nima
Effect of water jet orifice geometry on jet behaviour and cutting capability
2007-01-01 Annoni, MASSIMILIANO PIETRO GIOVANNI; Monno, Michele
Effects of manufacturing techniques on the mechanical properties of composite laminates
2002-01-01 Carvelli, Valter; D., de Angelis; Poggi, Carlo; R., Puoti
Effects of PVD DLC coating on 7075-T6 fatigue strength at high and low number of cycles
2016-01-01 Baragetti, Sergio; Gerosa, Riccardo; Villa, Francesco
Effects of severe air blast shot peening on microstructure and residual stress state of Al alloys
2010-01-01 Guagliano, Mario; Bagherifard, Sara; I., Fernandez Pariente; Ghelichi, Ramin
Effects of the interference level on the residual stresses in a cold-working expansion method
2014-01-01 Giglio, Marco; Lodi, M.; Giudici, Lorenzo
Experimental analysis on the Fatigue Threshold Behaviour of a Nitrided and Shot Peened Steel.
2007-01-01 Guagliano, Mario
Experimental comparison between traditional and cryogenic cooling conditions in rough turning of Ti-6Al-4V
2014-01-01 Tirelli, Stefano; Chiappini, Elio; Strano, Matteo; Monno, Michele; Semeraro, Quirico
Experimental evaluation of innovative tools for Ti-6Al-4V turning
2013-01-01 Strano, Matteo; Albertelli, Paolo; Chiappini, Elio; Tirelli, Stefano
Legenda icone
- file ad accesso aperto
- file disponibili sulla rete interna
- file disponibili agli utenti autorizzati
- file disponibili solo agli amministratori
- file sotto embargo
- nessun file disponibile